產品品牌：

BRIGHTY

產品型號：

壓力變送器2088

測量介質：

液體、氣體、水蒸氣

防護等級：

IP65

防爆等級：

IA2 II CT5

輸出信號：

4～20mADC

接口尺寸：

-0.1MPa～2MPa

電源電壓：

12～30VDC V

陶瓷電容型壓力變送器2088 Ceramic capacitive pressure transmitter 概述 2088陶瓷電容壓力變送器采用具有國際先進水平的陶瓷電容傳感器，配合高電子元件，經嚴格的工藝過程裝配而成。它采用無中介液的干式壓力測量技術。充分發揮了陶瓷傳感器的技術優勢，使壓力變送器具有優異的技術性能。它抗過載和抗沖擊能力強，穩定性高，并有很高的測量。2088陶瓷電容壓力變送器具有多種型號，多種量程，多種過程連接形式及材料。可廣泛用于石油、化工、電力、冶金、制藥、食品等許多工業領域，可適應工業測量的各種場合及介質，是傳統壓力表及傳統壓力變送器的理想升級換代產品，是工業自動化領域理想的壓力測量?jī)x表。 General overview 2088 ceramic capacitive pressure transmitter adopt the international advanced ceramic capacitive sensor and high accuracy electron components. It is the dry pressure technique without media liquid. The ceramic pressure transmitter has the incomparable advantage because of its good corrosion-proof, wear-proof, strike-proof and fine accuracy and stability. It has many type models, ranges, process connection types and material. It can be widely used for petrochemical, metallurgical, lectric power, pharmacy and food and so on. 特點 ● 抗過載和抗沖擊能力強 過壓可達量程的數倍至百倍。 ● 高，重復性好穩定性高 優于0.1%F.S/ 年。 ● 溫度漂移小由于取消了測量元件的中介液，因而使傳感器獲得了很高的測量，且受溫度影響小。 ● 抗干擾能力強 防水、防塵、防振、防爆、防腐。 ● 安裝簡便 產品結構合理，體積小，重量輕，可直接任意位置安裝。 Characters ● Excellent ability to resist the over loading and concussion ● High accuracy level, Good repetition, Good stability which better than 0.1%F.S/year. ● Temperature drift canceled the medium liquid, so the transmitter gets a better accuracy and the temperature can not make some effects for it. ● Anti-jamming, waterproof, dustproof, vibration-proof, explode-proof, corruption-proof. ● Easy to install, reasonable and compact structure, small weight. 工作原理 被測介質的壓力直接作用于傳感器的陶瓷膜片上，使膜片產生與介質壓力成正比的微小位移，正常工作狀態下，膜片位移不大于0.025毫米，電子線路檢測這一位移量后，即把這一位移量轉換成對應于這一壓力的標準工業測量信號。超壓時膜片直接貼到堅固的陶瓷基體上，由于膜片與基體間隙只有0.1 毫米，因此過載時膜 片的位移只能是0.1 毫米，所以從結構上保證了膜片不會產生過大變型，由于膜片采用高性能的工業陶瓷，因而使傳感器具有很強的抗沖擊及抗過載能力。 Working Principle The pressure of the medium direct effects the ceramic film of the transmitter and makes the film gets a little displacement. In the common condition, the displacement is less than 0.025mm and the electron wires can get the information of the displacement and transform it to be a standard industry measuring digital. Because the distance between the film and the ceramic body only is 0.1mm, the biggest displacement for the over pressure is 0.1mm. And the transmitter has the ability to resist the strong concussion and over loading. 技術參數 技術指標 使用對象: 液體、氣體或蒸汽 測量范圍: 表 壓：0～5KPa～6MPa; 負    壓：-0.1MPa～2MPa 輸    出: 4～20mADC 電    源: 12～30VDC 負載特性: 4～20mADC 二線制負載R ≤50(V-12) 溫度范圍: 環境溫度 -20～+70℃ ; 標準介質溫度 -20～+80℃ 外殼防護: 優于IP65 防爆類型: 本安型ia Ⅱ CT5(應外配安全柵) Technique Index Technique figures Mediums: Liquid, gas and stream Ranges: Positive pressure:0～5KPa～6MPa; Negative pressure：-0.1MPa～2MPa Output: 4～20mADC Power supply: 12～30VDC Loading: 4～20mADC two-line loading R ≤ 50(V-12) Temperature: Environment -20～+70℃ ; Standard Medium -20～+80℃ Case protection: Better than IP65 Explode-proof:Essential safety iaⅡCT5(Add safe bar outside)   性能指標 綜合: 等級：0.1%、0.25% 、0.5% 溫    漂：± 0.15%F.S/10℃ 穩 定 性：優于± 0.2% F.S/ 年 穩 定 性：優于± 0.1%BFSL/ 年 溫度影響：在-20～+70℃范圍內，變化量小于± 0.18%/10℃ 振動影響：在任何方向上振動頻率為20-200H時,變化量小于±0.02%BFSL/年 沖擊影響：任何方向100G沖擊11ms后，變化量小于± 0.02% BFSL 負載影響：只要輸入變送器的端子電壓高于12V，就無負載影響。 位置影響：安裝位置不影響零點 Capability figures Accuracy: Accuracy class: 0.1%、0.25%、0.5% Temperature drift: ± 0.15%F.S/10℃ Stability: Better than ± 0.2% F.S/Year Stability: Better than ± 0.1%BFSL/year Temperature effects: In the scope of -20～+70℃, the change is less than ± 0.18% / 10℃ Vibration effects: Under the vibration frequency of 20-200Hz，the change is less than ±0.02% BFSL/year Concussion effects: After the concussion of 100G for 11ms,the change will be less than ± 0.02% BFSL Loading effects: Make sure the end voltage higher than 12V，there will be on loading effects Position effects: Installing place can not effect the zero point. 結構指標 結構材料：膜片：氧化鋁陶瓷 外    殼：低銅鑄鋁 接觸介質材料：SUS304;（或SUS316及SUS316L可選） 過程連接：標準提供M20×1.5外螺紋 (或者其它約定要求) 電氣連接：可根據需要從任何一個出口引出，建議使用φ10工業電纜作為引線，以便密封，引出接頭可選用通用電纜接頭PG16或M20× 1.5，不引線一端用端蓋封住。 Structure figures Material: Film: Alumina ceramic Case: Low copper casing aluminum Wetted parts: SUS304；（or SUS316 and SUS316l foroptions） Process Connection: Standard M20×1.5 male thread(or other special requests) Electric connection: It is better to choose φ10 industry wire connect from any exit. The connect end can be PG16 or M20 × 1.5，and seal the other end.

五、系統連接及調試 變送器在測量系統中的連接見圖3。建議電源電壓Us 選用24V.DC。 二次儀表中采樣電阻（負載電阻）RL 的阻值選用250 Ω。如果Us 和RL 選用別的數值，那么RL= Vs-12/ 0.02 值 不能超過由公式計算得到的數值。 變送器頂部?jī)蓚?cè)面的連接孔用電纜密封或信號線裝配，信號電纜通過緊固螺母鎖緊，不用的連接口必須密封。 五、Connection and debugging See the chart as follow. Suggest the supply Us to be 24V. The connected gauge should be RL=250Ω。If you choose other date for Us and RL，the RL can not exceedRL= Vs-12/ 0.02 . Use wires to seal the holes on the sides of the transmitter or install the signal wire to the holes and fix by tight nut. The hole without used should be sealed. 如果使用的是本質安全防爆儀表，必須與安全柵配套使用，組成本安防爆系統。 If it is the essential safety pressure gauge, it is necessary to fit with the safe bar to form the essential safety system as following:   出廠前壓力變送器已按訂貨要求調試合格，用戶無需再做調整。長時間使用后如需重新標定，可分別調整“調零電位器”和“調量程電位器”。壓力量程的下限值對應4mA，上限值對應20mA. The transmitter has been debugged as the customer’s request, no need to debug again. After long time of using, if needed, it can be debugged by adjust“ Zero electric device” and“ Range electric device”. The down limit of the range should be corresponding with 4mA，and up limit will be with 20mA. 六、安 裝 1. 直接安裝在測量點上（任意角度）。 2. 盡量安裝在溫度梯度與溫度波動小的場合，同時避免強振動和沖擊。 3. 測量蒸汽或其它高溫介質時，注意不要使變送器的工作溫度超限。必要時，請安裝散熱裝置或其它冷卻裝置連接。 4. 安裝時應在變送器和介質之間加裝壓力截止閥，以便檢修和防止取壓口堵塞而影響測量。在壓力波動范圍大的場合還應加裝阻尼器或壓力緩沖裝置。 六、Installation notes 1. Direct install to the measuring point（any angles）. 2. It is better to be with less temperature fluctuation and avoid the strong vibration. 3. While measuring the high temperature mediums, please do not exceed the temperature limitation. If necessary, fit it with cooling devices. 4. Add pressure cut-off valve between the transmitter and the medium and add the dampers if the pressure changes a lot.   產品詳細資料請點擊：陶瓷電容型壓力變送器2088.pdf 變送器、壓力變送器、陶瓷電容型壓力變送器2088   本公司經營陶瓷電容型壓力變送器2088，質量保證，歡迎咨詢洽談。